Machine Shop

Chevy Tahoe 5.3 LS Engine Block, Crankshaft and Connecting Rods Machining Rebuild

Here's a Chevy GM LS engine block, crankshaft, connecting rods & Sealed Power forged pistons ready to go. We got lucky with the ARP hardware again!! We set the connecting rods up with a set of ARP rod bolts & reconditioned them accordingly. The main studs were torqued in place & the housing bore was [...]

2021-10-13T18:14:30+00:00October 13th, 2021|Machine Shop|

Chevy GM LS Aluminum Block Machining with ARP Main Studs

This is an aluminum Chevy, or GM, LS1 block we are machining. We fitted the block with a set of ARP main studs for line boring & align honing the housing bore where the main bearings go. After boring the cylinders for new oversize pistons in the boring machine, a torque plate was torqued in [...]

2021-10-08T13:14:35+00:00October 8th, 2021|Machine Shop|

Chevy LS Block Cylinder Boring and Honing For Wiseco Forged Pistons

This is a GM Chevy LS engine block we did some machine work to. We first did a line bore to the mains with ARP main studs & then align honed the housing bore to the finished size. We then bored & torque plate honed the cylinders for some new Wiseco forged pistons. We then [...]

2021-10-01T05:44:28+00:00October 1st, 2021|Machine Shop|

Chrysler Dodge Hemi Engine Block Boring, Honing and Line Bore Machining

This is a Chrysler, or Dodge, 354 cubic inch engine block we did the machine work to. After thermal cleaning, shot blasting & magnafluxing the block for cracks, we bored the cylinders for some new oversize forged Ross Racing Pistons. We then finish honed the cylinders to size with a torque plate installed. The housing [...]

2021-09-29T05:34:16+00:00September 29th, 2021|Machine Shop|

Chevy Inline Six Cylinder Stovebolt Engine Machining and Rebuild

This is an inline six cylinder, or straight six, Chevy engine we're finishing up the rebuild to. The engine originally had an integral cylinder head but we are fitting it with a non-integral cylinder head. Meaning the intake & exhaust manifolds are both separate from the head & bolt in place rather than casted as [...]

2021-09-25T03:24:17+00:00September 25th, 2021|Machine Shop|

High Performance Muscle Car 427 Big Block Chevy Engine Machining and Rebuild

Here’s some progress pics of a 427 cubic inch big block Chevy engine we're building. We performed all the machine work to the block, crankshaft, connecting rods & cylinder heads including balancing the rotating assembly. The internal parts consist of Sealed Power forged pistons, Hastings moly rings, Clevite rod & main bearings, Melling high volume [...]

2021-09-22T23:35:18+00:00September 22nd, 2021|Machine Shop|

1945 International Truck KB5 Green Diamond Flathead Engine Machining and Rebuild

Here’s some pics of a 1945 Green Diamond KB5 flathead inline six cylinder engine we rebuilt. The engine is out of an International truck that is getting completely restored. We performed all the machine work to the block, crankshaft, connecting rods & cylinder head. After completing all the machine work we detailed all the pieces [...]

2021-09-17T19:26:47+00:00September 17th, 2021|Machine Shop|

Grader Circle Drive Motor Plate Machining

This is a steel plate for the circle drive motor on a Caterpillar grader circle. The plate is a little over an inch thick. In order to get the proper engagement between the pinion gear & the teeth segments of the circle assembly the plate needs to be thinner. After writing the program the spindle [...]

2021-09-08T01:34:39+00:00September 8th, 2021|Machine Shop|

Arctic Cat Wildcat XX and Yamaha YXZ Cylinder Head Surface Machining For Higher Compression and MLS Head Gasket

Here's an aluminum cylinder head that came in to have its surface machined, or milled. The head is off of an Arctic Cat Wildcat XX which is the same three cylinder engine that is used in the Yamaha YXZ side-by-side. Motor Mission Machine & Radiator 5435 Desert Point Dr. Las Vegas, Nv. 89118 Ph: (702) [...]

2021-08-27T02:14:28+00:00August 27th, 2021|Machine Shop|

High Performance Dodge, Chrysler, Plymouth 440 V8 Engine Block Machining

Here's a completed 440 Dodge, or Chrysler, V8 engine block. We first performed a magnaflux to make sure there are no cracks. We then line bored the housing bore which is fitted with billet main caps & hardened main studs. We then bored & torque plate honed the cylinders for a set of iCon forged [...]

2021-08-20T00:24:48+00:00August 20th, 2021|Machine Shop|
Go to Top