Industrial & Heavy Equipment

Caterpillar and Komatsu Oscillating Loader Axle Trunnions, Supports and Parts Repair and Reconditioning

Here's some oscillating loader axle Trunnions & Supports we recently finished repairing & reconditioning. These Trunnions & Supports are for a Komatsu WA1200 loader. The bores all had to be machined, welded & then bored back to spec. The mounting surface pads also required welding & surfacing. The oring seal grooves and counterbores all required [...]

2019-07-19T15:21:56+00:00July 19th, 2019|Industrial & Heavy Equipment|

Cat Dozer Equalizer Bar Bore Welding and Boring Repair

Here's a couple of Caterpillar dozer equalizer bars we reconditioned. The bores were worn & needed to be welded & then bored back to the proper size. Motor Mission Machine & Radiator 5435 Desert Point Dr. Las Vegas, Nv. 89118 Ph: (702) 649-2366 or (702) 649-0648 Fax: (702) 649-4133 www.MotorMission.com Facebook.com/MotorMission

2019-07-16T23:41:49+00:00July 16th, 2019|Industrial & Heavy Equipment|

Komatsu WA1200 Loader Trunnion Bore Repair and Machining On Rottler EM105H Multipurpose CNC Machine

This is our new Rottler EM105H multipurpose CNC machining center. It is based off of an F105. We have a front & rear trunnion on it for a Komatsu WA1200 loader. The trunnions require bore welding & machining as well as surfacing of their mounting pads. The engine block is a 5.9 Cummins diesel that [...]

2019-07-13T02:12:01+00:00July 13th, 2019|Industrial & Heavy Equipment|

Berkeley Pump For Pumping Water and Slurry

This is a Berkeley pump that came in for rebuilding. It had rocks lodged inside of it to the point it was locked up & wouldn't spin. It pumps slurry which contains water, mud & heavy debris. We reconditioned it back to new & ready for another service life. Motor Mission Machine & Radiator 5435 [...]

2019-07-10T01:05:05+00:00July 10th, 2019|Industrial & Heavy Equipment|

Komatsu HD785 Haul Truck Transporting On A Radiator Delivery and Pick Up Trip

Here's a Komatsu HD785 haul truck we encountered while on one of our own radiator delivery & pick up trips. Up in mining country we often have to pull off to the side of the road to make room for the large mining equipment that's being transported on the roads. Motor Mission Machine & Radiator [...]

2019-06-07T16:05:24+00:00June 7th, 2019|Industrial & Heavy Equipment|

Hitachi EX5500 Hydraulic Shovel Hydraulic Oil Coolers

Here's a set of hydraulic oil coolers for a Hitachi EX5500 hydraulic shovel. We recored these coolers with heavy duty high efficiency cores. The EX5500 takes four of these coolers. Motor Mission Machine & Radiator 5435 Desert Point Dr. Las Vegas, Nv. 89118 Ph: (702) 649-2366 or (702) 649-0648 Fax: (702) 649-4133 www.MotorMission.com Facebook.com/MotorMission [...]

2019-05-31T00:11:04+00:00May 31st, 2019|Industrial & Heavy Equipment|

Cat 793 Dog Bone Bore Welding, Machining , Boring and Repair

Here's a Caterpillar 793C dog bone that we reconditioned. We removed the bearings from the bores & checked the dogbone for any cracks & defects. We then machined the bores out & then welded them so we could bore them back to the proper spec. After painting we pressed some new bearings in place. Motor [...]

2019-05-09T20:21:58+00:00May 9th, 2019|Industrial & Heavy Equipment|

Caterpillar 793C Steering Bellcrank Y-Link Tapered and Split Bore Repair

Here's a Cat 793C haul truck steering bellcrank Y-link that we repaired & reconditioned the bores on. The split bore we machine & counterbore for a hardened split bore flanged sleeve to go in place. The two smaller bores are tapered bores that get machined for hardened tapered ID sleeves that we press in & [...]

2019-05-01T03:16:05+00:00May 1st, 2019|Industrial & Heavy Equipment|

Cat 16H Grader Circle and Drawbar with Blade Repair and Rebuild

Here's a Cat 16G or H grader circle & drawbar assembly with the blade we repaired & overhauled. It needed lots of cracks welded up along with some extensive machining. We also rebuilt the circle drive motor which had a damaged pinion. We got it all spruced up & ready for another round of service. [...]

2019-04-10T01:06:28+00:00April 10th, 2019|Industrial & Heavy Equipment|